ramuc type ep epoxy pool paint

2021/05/21

Happy shopping! EP Epoxy cures to a hard, tough, durable finish, providing stain, chemical and abrasion resistance for protection of concrete, plaster and fiberglass swimming pools, spas and slides. With its hard, tough, durable finish, epoxy provides unsurpassed stain, chemical, and abrasion resistance. Coverage: 175-200 sq. At 65 the induction time is 60 minutes. Use dark colors for accent painting only. ft. on recoats (actual coverage will vary and is dependent upon the texture and profile of the surface), Minimum dry film per coat - 5 mils dry (7.5 mils wet), Maximum dry film per coat - 8 mils dry (12.5 mils wet), Pot life - 3 hours @ 70 F. and 50% relative humidity. This item is eligible for return within 30 days of shipment. Apply at the recommended coverage rate. ramuc ramuc epoxy Packaged in an easy-to-use 1-to-1 mix ratio, Type EP Hi Build Epoxy rolls easily and builds up to 8 mils dry per coat rendering "smoothing" qualities on rough surfaces. gallon epoxy aqua ep pool paint type EP Epoxy cures to a hard, tough, durable finish, providing stain, chemical and abrasion resistance for protection of concrete, plaster and fiberglass swimming pools, spas and slides. We're sorry, we are unable to accept Mastercard's that start with the new 2 prefix at the beginning of your card number. It is the mission of Waterline Technologies to be recognized as a knowledgeable and reliable source for the aquatic industry. ft. per gallon kit on bare, sand blasted or rough surfaces, 400-450 sq. Eligible promotions or discounts will be calculated during checkout. Water blast the surface to remove loose paint and dirt. After all cleaning in completed, allow the pool surface to dry. Follow the manufacturers recommendations. EP Epoxy has been a proven performer for more than 50 years. ), Minimum dry film per coat: 1.7 mils dry (2..9 mils wet), Maximum dry film per coat : 2.0 mils dry (5.7 mils wet). All epoxy films will chalk (break down from the UV rays of the sun) over a period of time. This website uses cookies and other tracking technologies (also known as pixels or beacons) to aid your experience (such as viewing videos), as well as performance cookies to analyze your use of this website and to assist with marketing efforts. ramuc

EP Epoxy cures to a hard, tough, durable finish, providing stain, chemical and abrasion resistance for protection of concrete, plaster and fiberglass swimming pools, spas and slides. 400-450 sq. This is a natural degradation of the top surface of the epoxy film. Ajoute une paisseur supplmentaire sur la paroi de bton.

Remove the plastic and wait 24 hours to perform the test again. Lower temperatures and higher humidity will affect the final cure of the coating. EP Epoxy cures to a high gloss-finish with excellent coverage rates, especially on previously painted epoxy surfaces. If condensation has formed underneath the plastic then the surface is not dry enough to paint. Abrasion material used to create a medium grade sandpaper profile for fiberglass surfaces or previously painted epoxy surfaces: Sandpaper #80 grit, power sander, or wire brush, 5 gallon bucket for boxing (intermixing) paint, Mechanical mixer (this simply can be a paddle attachment, Ramuc Thinner or xylene for thinning paint, cleaning-up tools and spills. EP Epoxy has been a proven performer for more than 50 years. We look forward to fulfilling your order for you. techtips/TechHiBuild.jpg. Previously painted epoxy or bare fiberglass surfaces need to be abraded to a #80 grit profile. Please view our return policy or contact us for details. EP Epoxy has been a proven performer for more than 50 years. Find the steps for proper surface preparation, Protects previously painted epoxy or unpainted surfaces, Excellent choice for waterpark facilities, including slides, VOC compliant everywhere in US and Canada, Eight-hour "pot life" when component A and B are mixed together, RAMUC EP EPOXY AQUAGREEN GALLON POOL PAINT, RAMUC EP EPOXY VERMILLION GALLON POOL PAINT. Let us help you determine which product to use, how much will be needed and how to properly apply the coating. Let us help you determine which product to use, how much will be needed and how to properly apply the coating. EP Epoxy cures to a high gloss-finish with excellent coverage rates, especially on previously painted epoxy surfaces. Ideal air temperatures for application are between 50-90F. Aged plaster should be checked for integrity.

Wait three hours to determine if condensation has formed underneath the plastic. Application & Technical Data Meilleure rsistance aux produits chimiques, UV, dcoloration et au farinage. techtips/TechHiBuild.jpg. Proposition 65 Warning for California Customers, Warning: Cancer and Reproductive Harm - www.P65Warnings.ca.gov/, Phone: 800.437.8072 Local: 701.222.4860, 2022 Recreation Supply Company, All Rights Reserved. Because of their chemical cure, epoxies are the paints of choice for indoor pools. Because of their chemical cure, epoxies are the paints of choice for indoor pools. If rain occurs during the curing process, allow an extra day of dry time for each day of rain. For compatibility purposes, the existing paint on previously painted surfaces of a pool or spa should be determined before painting.

A chalky substance can be created by over treating the water with shock, bromine, ozone and ionization. ft./gallon on recoats. If you click the "Accept All Cookies" button or continue navigating the website, you agree to having those first and third-party cookies set on your device.

- Durability expectation of 1 to 2 seasons and more depending on maintenance. Mechanically mix Part B for approximately 10 minutes. Ramuc, PREMIUM LOW-FILM BUILD EPOXY AQUATIC COATING, This website uses cookies and other tracking technologies (also known as pixels or beacons) to aid your experience (such as viewing videos), as well as performance cookies to analyze your use of this website and to assist with marketing efforts.

All surfaces should then be acid etched with a 15-20% solution of muriatic or sulfamic acid to achieve a medium grade sandpaper finish on bare concrete or plaster and to remove mineral deposits on previously painted epoxy surfaces. Could you please try another card or if you would like to still use your Mastercard, we can accept it through PayPal instead. By following these simple 1-2-3 steps, you're ensuring virtually maintenance-free paint service on your pool. ft./gallon on bare, sandblasted, or rough surfaces. Proper preparation is required to achieve the desired finish you expect. For more information on how we use Cookies, please read our Privacy Policy.

Continue with the test until no condensation forms underneath the plastic after the three-hour wait period. Then, scrub the entire pool with a soap/tri-sodium phosphate (TSP) solution to remove all dirt, oils, loose or peeling paint, and chalk. If you do not wish to accept cookies from this website, you can choose to not allow cookies from this website by updating your browser preferences. It is extremely durable in fresh and salt water and is resistant to chemicals commonly used in swimming pools, including chlorine. This item is classified as ORM-D. Additional charges for expedited shipping may apply. Epoxy Pool Coating is a two component polyamide coating specially designed to properly prepare concrete, lime mortar, gunite, fiberglass and steel pools. Please try again!!

Ramuc Thinner can be used to thin paint by 10%. Average dry times vary regionally and are dependent upon the porosity of the surface. Rain or moisture can cause blistering, color blushing, and the finish could be altered. Check for hollow or weak/crumbling plaster by using a ball-peen hammer or any other comparable method. If mixing more than the one - 2 gallon kit at a time, intermix the kits to ensure color uniformity.

This coating can be applied directly to new surfaces or to surfaces already coated with epoxy. Neutralize/Rinse with TSP and water. Subtotal doesn't include shipping or tax. The "shock" of calcium hypochlorite can cause a white, bleached look to the paint film, leaving a whitish deposit. Visitez le groupe priv le plus populaire au Canada . Note: Colors are representative of the actual product color.

The keys to a successful pool or deck paint job are proper SURFACE PREPARATION AND CORRECT APPLICATION. Additionally, surface preparation is one of the most important steps in painting a pool. EP Epoxy cures to a high gloss-finish with excellent coverage rates, especially on previously painted epoxy surfaces. Proper preparation is required to achieve the desired finish you expect. Primer - all Ramuc paints are self-priming, 75-125 sq. We will provide our customers with satisfaction, technical support, education and honesty with solutions at competitive prices.

This ensures the surface is dry enough to apply epoxy paint. It is recommended to wait five dry days and then perform a condensation test to determine surface dryness. If you order this item and specify an expedited shipping method, you will be contacted with a quote for any additional charges that may apply. Ramuc EP Hi Build Epoxy Pool Paint Application Guide, Several two-foot square transparent pieces of plastic.

Also, because of their chemical cure, epoxies are the paints of choice for indoor pools, spas, and whirlpools.

and Cellulose Fiber Media, Grate Ideas America-The-Grate PVC Grating, Parts - Racing Lane Lines and Storage Reels, Technical Bulletin and Application Guide Ramuc Type EP Epoxy, Protects previously painted epoxy or unpainted surfaces, Excellent choice for waterpark facilities, including slides, VOC compliant everywhere in US and Canada. Allow the admixed paint to set for 15-30 minutes (induction time) prior to use at 70 F. and 50% relative humidity. Mechanically mix Part A for approximately 10 minutes. Because of their chemical cure, epoxies are the paints of choice for indoor pools.

To determine dryness, perform this simple test - Duct tape 2' x 2' pieces of transparent plastic to the deep end wall and floor, and on several other areas of the pool. If existing surface is unknown, a sample should be submitted for testing to determine the type of existing surface. Ramuc EP Hi Build Epoxy offers the longest lasting protection for concrete, plaster, gunite, and fiberglass swimming pools and spas. ft. on bare, sandblasted, or rough surfaces, 125-200 sq. If you click the "Accept All Cookies" button or continue navigating the website, you agree to having those first and third-party cookies set on your device. To recoat - 16-72 hours. Should any minor repairs need to be made, such as hydraulic cement patch or crack joint filling, do them at this time. Surface temperature should be at least 50F. Additionally, surface preparation is one of the most important steps in painting a pool. We will not process your order until you have approved the extra charge. Mechanically mix both Part A and Part B together for approximately 15 minutes. Super-chlorinated water may cause a "bleached-out" look.

Poles & Handles (Eligible for Free Shipping), Diatomaceous Earth (D.E.)

For more information on how we use Cookies, please read our, Protects previously painted epoxy or unpainted surfaces, Excellent choice for waterpark facilities, including slides, VOC compliant everywhere in US and Canada. Great for Koi ponds, hot tubs, spas and fountains. Coverage: 175200 sq. Pool paint is not a Band-Aid for weak surfaces. EP Hi Build Epoxy is self-priming; no other type of primer is recommended or should be used. Simply click the "Pay by PayPal" link to do so. Iron in the water from rust in the filter system may leave deposits and stain the fil. ft. per gallon kit on re-coats (Actual coverage will vary and is dependent upon the texture and profile of the surface. Plaster, concrete, or gunite surfaces should be tested for integrity and soundness. If second coat is applied beyond 72 hours, the first coat must be abraded/sanded prior to applying second coat. Use no more than a 3/8" nap roller made for solvent based paint. Painting is one of the best ways to protect and beautify your Get the latest updates on new products and upcoming sales. It is not the paint breaking down.

If you do not wish to accept cookies from this website, you can choose to not allow cookies from this website by updating your browser preferences.

We've encountered an error. General Surface Preparation Screen monitor settings and printer ink may cause variability. Find the steps for proper surface preparation HERE. document.getElementById('copyright2').appendChild(document.createTextNode(new Date().getFullYear()))

EP Hi Build has a pot life (use life) of 3 hours. We suggest a natural polymer product or clarifier that can reduce the chalking problem. For bare concrete, fiberglass, plaster and previously painted epoxy. Care needs to be taken when recoating epoxy surfaces to remove all tightly adhering residual chalk. Perform repairs to the plaster before painting. Paint chips can be taken to any Ramuc distributor/dealer to be forwarded to the Ramuc laboratory for analysis. The pool is filled too soon (see cure rates) before the paint is completely cured, causing a blush over the surface which looks like fading or chalking. Immediately after the pool is emptied, begin the preparation process.