transparent epoxy paint

2021/05/21

RESTRICTIONS: Restrict the use of the floor to light traffic and non-harsh chemicals until the coating is fully cured (see technical data under full cure). GARDNER VARIABLE IMPACTOR: 50 inch pounds direct passed We sell many types of 100% solids epoxy. This is a product guide to help you decide which epoxy is best for you. PRIMING: A suitable primer should be used before applying this product. SOLIDS BY WEIGHT: 100% HARDNESS: Shore D = 80. ULTIMATE ELONGATION: 4.1% If concrete conditions or over aggressive mixing causes air entrapment, then an air release roller tool should be used prior to the coating tacking off to remove the air entrapped in the coating. 100% solids epoxy is considered the industry standard for high-end flooring due to the fact that it is 4x stronger than concrete and has no voc, no flammability and can be applied as thick or thin as you need it. We recommend topcoating with a urethane product to assist in UV-resistance.

COLOR: Clear FINISH CHARACTERISTICS: Gloss (70-95 at 60 degrees @ Erichsen glossmeter) This gives it the name '100% solids.' Ideal for full broadcast terrazzo or colorchip floors. The material in the transfer pail is now ready to be applied onto your base coat. Ideal for full broadcast terrazzo or colorchip floors. A test should be made to determine that the concrete is dry; this can be done by placing a 4'x4' plastic sheet on the substrate and taping down the edges. GARDNER VARIABLE IMPACTOR: 50 inch pounds direct passed Improper mixing may result in product failure. They are in pre-measured kits and should be mixed as supplied in the kit. SOLIDS BY VOLUME: 100% (+/- 1%)

Standard packages are in pre-measured kits and should be mixed as supplied in the kit. Always remember that colder temperatures will require more cure time for the product before recoating or topcoating can commence. These cookies will be stored in your browser only with your consent. Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. We sell 100% solids epoxy in both colored and clear. HARDNESS: Shore D = 81 If concrete conditions or over aggressive mixing causes air entrapment, then an air release roller tool should be used prior to the coating tacking off. recoat or topcoat: 8-12 hours @ 70 degrees F SOLIDS BY WEIGHT: 100% COMPRESSIVE STRENGTH: 9,100 psi @ ASTM D695 1/2" X 1/2" bars Many epoxy coatings and urethanes as well as multiple coats of this product are compatible for use as a topcoat. PRODUCT APPLICATION: The mixed material can be applied by brush or roller. If you are looking for colored epoxy, check out Norklad 200, which is available in 12 different colors. 100% solids is the industry standard for high-end commercial epoxy flooring. .75 Gallon (75-100+ sq/ft) Tack free (dry to touch): 6-8 hours @ 70 degrees F TOPCOAT: Urethane topcoat is recommended for added UV-Resistance if exposed to sunlight. When applied at 100 sq/ft per gallon, Norklad 100-UV willself-levelto a glasslike surface. MIX RATIO: 9.0 pounds part A (.99 gallons) to 4.15 pounds part B (.49 gallons) (volumes approx.) Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. wood uv clear deck finish stain finishes resistant exterior epoxy olympic defy fence semi maximum redwood siding transparent sikkens cabot PRODUCT MIXING: This product has a mix ratio of 12# part A to 4.15# part B or two parts A to one part B by volume for standard colors. Low odor, low VOC formula is ideal for use on interior coated or bare concrete surfaces including garages, basements, workshops and more, Your email address will not be published. SURFACE PREPARATION: The most suitable surface preparation would be a fine brush blast (shot blast) to remove all laitance and provide a suitable profile. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating. They are in pre-measured kits and should be mixed as supplied in the kit. Some of our DIY customers have had great success by carefully researching and buying the proper tools, but know that if you have never installed a 100% epoxy floor before, you are taking a risk by doing so. light foot traffic: 12-14 hours @ 70 degrees F We recommend topcoating with a urethane product to assist in UV-resistance. We highly recommend that the kits not be broken down unless suitable weighing equipment is available. COMPRESSIVE STRENGTH: 11,200 psi @ ASTM D695 If concrete conditions or over aggressive mixing causes air entrapment, then an air release roller tool should be used prior to the coating tacking off. All dirt, foreign contaminants, oil and laitance must be removed to assure a trouble free bond to the substrate. COVERAGE PER GALLON: 90-100 square feet per gallon @ 16-18 mils When applied at 100 sq/ft per gallon, Norklad 100-M will self-level to a glasslike surface. COLORS: Light Gray, Medium Gray, Charcoal, Off White, Beige, Tan, Wheat, Taupe, Tile Red, Royal Blue, Steel Blue, Black, White soapstone valspar polymers PACKAGING INFORMATION: 3 gallon kits (2.9 3.0 gallons net approximately) VISCOSITY: Mixed = 700-1000 cps (typical) i. When to use Norklad 100-M: 100% solids is recommended for warehouses, kitchens, restrooms, and other areas where either a high build clear product is needed or where a decorative filled floor is desired. Slip Resistant Floor Coating Grit Additives. HARDNESS: Shore D = 81 Maintain temperatures and relative humidity within the recommended ranges during the application and curing process. However, all previous coats should be deglossed to insure a trouble free bond prior to application of recoats or topcoats. It is mandatory to procure user consent prior to running these cookies on your website. Standard packages are packaged in 1.5-gal kits. After mixing, transfer the mixed material to another pail (the transfer pail) and again remix. pot life 1 1/2 gallon volume: 30-50 minutes @ 70 degrees F MIX RATIO: 12 pounds (1 gallon) part A to 4.15 pounds (.50 gallons) part B (volumes approx.) conductive potting thermally ABRASION RESISTANCE: Taber abraser CS-17 calibrase wheel with 1000 gram total load and 500 cycles = 36 mg loss PRODUCT APPLICATION: The mixed material can be applied by brush, roller or a serrated squeegee and then back rolled as long as the appropriate thickness recommendations are maintained. APPLICATION TEMPERATURE: 55-90 degrees F, pot life 1 1/2 gallon volume .. 20-30 minutes @ 70 Ftack free (dry to touch)6-8 hours @ 70 Frecoat or topcoat.. 10-16 hours @ 70Flight foot traffic..14-18 hours @ 70Ffull cure (heavy traffic) 2-7 days @ 70F, CHEMICAL RESISTANCE:REAGENT RATINGbutanol Cxylene C1, 1, 1 trichloroethane BMEK Amethanol Aethyl alcohol Cskydrol B10% sodium hydroxide E50% sodium hydroxide D10% sulfuric acid C70% sulfuric acid A10% HC1 (aq) C5% acetic acid B. Apply your basecoat and colorchips and allow to sufficiently cure. (wait until you can no longer leave an imprint of your finger in the coating.) Light foot traffic: 14-18 hours @ 70 degrees F full cure (heavy traffic): 2-7 days @ 70 degrees F, APPLICATION TEMPERATURE: 60-90 degrees F with relative humidity below 85%, SOLIDS BY WEIGHT: 100% (+/- 1%) All dirt, foreign contaminants, oil and laitance must be removed to assure a trouble free bond to the substrate. GARDNER VARIABLE IMPACTOR: 50 inch pounds direct passed If used alone, it is recommended that a primer coat be used to prevent outgassing/blistering. VOLATILE ORGANIC CONTENT: Zero pounds per gallon COVERAGE PER GALLON: 53-130 square feet per gallon @ 12-30 mils RECOAT OR TOPCOATING: If you opt to recoat or topcoat this product, you must first be sure that the coating has tacked off before recoating. Colder temperatures will require more cure time for the product before recoating or topcoating can commence. 100% solids epoxy does not have water or solvents that evaporate while curing; it retains 100% of its thickness and body after cure. After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. 1.5 Gallon (175+ sq/ft) VOLATILE ORGANIC CONTENT: Zero pounds per gallon 100% solids epoxy is the only epoxy that can be used for metallic epoxy floors (pictured above). RECOAT OR TOPCOATING: If you opt to recoat or topcoat this product, you must first be sure that the coating has tacked off before recoating. It is best to let the floor remain dry for the full cure cycle. Best of all, they are abrasian resistant, chemical resistant, stain resistant, and all-around the most durable floor coating there is, by far. FINISH CHARACTERISTICS: Gloss (60 to 90 @ 60 degrees @ Erichsen glossmeter)

FLOOR CLEANING: Caution! COVERAGE PER GALLON: 90-100 square feet per gallon @ 16-18 mils Before recoating or topcoating, check the coating to insure no epoxy blushes were developed (a whitish, greasy film or deglossing). FINISH CHARACTERISTICS: Gloss (60 to 90 @ 60 degrees @ Erichsen glossmeter) By continuing to use this site, you accept our, 1 gal Rust-Oleum Brands 292514 Clear EpoxyShield Premium Clear Coating, polyurethane has many advantages over epoxy, home improvement centers and paint stores harm more than help, How to Fix or Prevent a Rough Textured Color Flake Coating, G-Floor Garage Mats Review | We Reveal The Good And The Bad, The Poor Reviews and Ruined Expectations of Garage Floor Coatings, Street Outlaws Ryan Martin Applies Nohr-S Polyurea Coating System to His New Shop Floor, How to Eliminate Pet Urine Odors from Concrete and Basements, How To Prep and Recoat an Older Epoxy Floor for a New Coat, What You Should Know About Interlocking Garage Floor Tiles, Why the Best DIY Floor Coating Kits are Single-Part Polyurea, Tips for Filling Contraction and Expansion Joints, How to Easily Repair Your Pitted and Spalled Concrete, Rust Bullet, A Long Lasting Garage Floor Paint has Arrived. We also use third-party cookies that help us analyze and understand how you use this website. *For best results, apply with a nap roller and/or squeegee ADHESION: 450 psi @ elcometer (concrete failure, no delamination) SOLIDS BY VOLUME: 100% Norklad 100-M is a two component 100% solids epoxy broadcast coat that can be filled with decorative chips and colored sand mixtures to provide an infinite array of color schemes or patterns. Required fields are marked *, This website uses cookies for the best browsing experience. SURFACE PREPARATION: The most suitable surface preparation would be a fine brush blast (shot blast or diamond grind) to remove all laitance and provide a suitable profile. (1 gal of part a (resin) and half gallon of part b (hardener). Norklad 100-M can easily coat over any solvent or waterborne epoxies. COLOR: Clear Improper mixing may result in product failure. Test each cleaner in a small area, utilizing your cleaning technique. The material in the transfer pail is now ready to be applied on the primed substrate. Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. tack free (dry to touch): 5-8 hours @ 70 degrees F SURFACE PREPARATION: The most suitable surface preparation would be a fine brush blast (shot blast or diamond grind) to remove all laitance and provide a suitable profile. COMPRESSIVE STRENGTH: 11,200 psi @ ASTM D695 VISCOSITY: Mixed = 700-1000 cps (typical) We highly recommend that the kits not be broken down unless suitable weighing equipment is available. The material in the transfer pail is now ready to be applied onto your basecoat. Pot life - 1 1/2 gallon volume: 20-30 minutes @ 70 degrees F PRODUCT STORAGE: Store product at normal room temperature. All rights reserved | Privacy Policy | Terms of Use. FLEXURAL STRENGTH: 7,400 psi @ ASTM D790 But opting out of some of these cookies may affect your browsing experience. It is 100% solids therefore has low odor, no flammability, and is self-leveling. FLEXURAL STRENGTH: 7,400 psi @ ASTM D790 This product can be used with random chip broadcasts, full chip broadcasts, or colored quartz. A properly installed 100% solids floor will last for 20 years or more.However, 100% solids epoxy has an extremely short potlife and cure time of only 30 minutes. After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. CURE SCHEDULE: Apply your base coat and colorchips and allow to sufficiently cure. We apologize for this inconvenience. NOTE: extensive chemical resistance information is available through your sales representative. If a blush is present, it must be removed prior to topcoating or recoating. TOPCOAT: Urethane topcoat is recommended for added UV-Resistance if exposed to sunlight. (1 gal of part a (resin) and half gallon of part b (hardener). It must be applied quickly and skillfully with a notched squeegee by a professional or there is a high likelihod that it will cure faster than it can be applied. Orders placed over the next few months may be delayed or will be refunded.

Standard packages are packaged in 1.5-gal kits. APPLICATION TEMPERATURE: 55-90 degrees. SOLIDS BY VOLUME: 100% These cookies do not store any personal information. A test should be made to determine that the concrete is dry; this can be done by placing a 4'x4' plastic sheet on the substrate and taping down the edges. (wait until you can no longer leave an imprint of your finger in the coating. See the front side of this technical data for primer information. PACKAGING INFORMATION 1.5 gallon kits (2.95 gallons net approximately) RECOMMENDED FILM THICKNESS: 16-18 mils FLEXURAL STRENGTH: 5,400 psi @ ASTM D790 PRODUCT MIXING: This product has a mix ratio of 9.0# part A to 4.15# part B. ADHESION: 350 psi @ elcometer (concrete failure, no delamination) Full cure (heavy traffic): 2-7 days @ 70 degrees F Norklad 100 can easily coat over any solvent or water based epoxies. The plastic sheet testing is also a good method to determine if any hydrostatic pressure problems exist that may later cause disbonding. However, the material can also be applied by a suitable serrated squeegee and then back rolled as long as the appropriate thickness recommendations are maintained. Before recoating or topcoating, check for epoxy blushes (a whitish, greasy film or deglossing). Improper mixing may result in product failure. Due to supply shortages throughout the entire chemical industry; we have limited supplies of various epoxy, urethane and color chip flakes. ABRASION RESISTANCE: Taber abraser CS-17 calibrase wheel with 1000 gram total load and 500 cycles = 36 mg loss Rating key: A - not recommended, B - 2 hour term splash spill, C - 8 hour term splash spill, D - 72 hour immersion, E - long term immersion. After mixing, transfer the mixed material to another pail (the transfer pail) and again remix. Necessary cookies are absolutely essential for the website to function properly. This product can be used with random chip broadcasts, full chip broadcasts, or colored quartz. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating.

It is 100% solids therefore has low odor, no flammability, and is self-leveling. TENSILE STRENGTH: 7,600 psi @ ASTM D638 If you are interested in a this kind of finish, check out our metallic epoxy floor kit page that includes complete kits and application instructions. You also have the option to opt-out of these cookies. PRODUCT MIXING: This product has a mix ratio of 9.0# part A to 4.15# part B. *For best results, apply with a nap roller and/or squeegee. Some cleaners may affect the color of the floor installed. MIX RATIO: 9.0 pounds part A (.99 gallons) to 4.15 pounds part B (.49 gallons) (volumes approx.) If you are looking for a basic clear coat, look no further than Norklad 100 M. If you are looking for a UV resistant clear coat, upgrade to Norklad 100 UV. ABRASION RESISTANCE: Taber abraser CS-17 calibrase wheel with 1000 gram total load and 500 cycles = 32 mg loss TENSILE STRENGTH: 4,800 psi @ ASTM D638 All dirt, foreign contaminants, oil and laitance must be removed to assure a trouble free bond to the substrate. Out of these, the cookies that are categorized as necessary are stored on your browser as they are essential for the working of basic functionalities of the website. If after 24 hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating. Before recoating or topcoating, check the coating to insure no epoxy blushes were developed (a whitish, greasy film or deglossing). SIZES: 100% solids is the industry standard for high-end commercial epoxy flooring. If no ill effects are noted, you can continue to clean with the product and process tested. RECOAT OR TOPCOATING: If you opt to recoat or topcoat this product, you must first be sure that the coating has tacked off before recoating. The base coat must be 100% solids because its self leveling properties allow the pigments to blend together and settle evenly. TENSILE STRENGTH: 7,600 psi @ ASTM D638 CLEANUP: Use xylol xylene. 3 Gallon (400+ sq/ft). After the two parts are combined, mix well with slow speed mixing equipment such as a jiffy mixer until the material is thoroughly mixed and streak free. Recoat or topcoat: 10-16 hours @ 70 degrees F This website uses cookies to improve your experience while you navigate through the website. This drawback of 100% solids epoxy can also be a positive; many professionals appreciate the fast potlife of 100% solids because it makes jobs faster and more efficient. Norklad 100-UV has additional UV inhibitors to slow down ambering in the presence of UV light. VOLATILE ORGANIC CONTENT: Nearly zero pounds per gallon ULTIMATE ELONGATION: 3.1% VISCOSITY: Mixed = 1300-2300 cps (typical, most colors) Always remember that colder temperatures will require more cure time for the product before recoating or topcoating can commence. When to use Norklad 100-UV: 100% solidsis recommended for warehouses, kitchens, restrooms, and other areas where either a high build clear product is needed or where a decorative filled floor is desired. If used alone, it is recommended that a primer coat be used to prevent outgassing/blistering. A test should be made to determine that the concrete is dry; this can be done by placing a 4X4 plastic sheet on the substrate and taping down the edges. This category only includes cookies that ensures basic functionalities and security features of the website. RECOMMENDED FILM THICKNESS: 16-18 mils

ULTIMATE ELONGATION: 4.1% We highly recommend that the kits not be broken down unless suitable weighing equipment is available.

Norklad 100-UV is a two component 100% solids epoxy broadcast coat that can be filled withdecorativechips and colored sand mixtures to provide an infinite array of color schemes or patterns. Then broadcast aggregate into the coating while wet. If you are ready to purchase, head to our webstore. Continuous storage should be between 60 and 90 degree F. Low temperatures or temperature fluctuations may cause product crystallization. ADHESION: 350 psi @ elcometer (concrete failure, no delamination) PRODUCT APPLICATION: The mixed material can be applied by brush, roller or a serrated squeegee and then back rolled as long as the appropriate thickness recommendations are maintained. RECOMMENDED FILM THICKNESS: 12-30 mils It's recommend to squeegee this product out and apply 100-125 sq/ft per gallon (approx.14-16 mils) and back roll it with a shed-resistant roller to even it out. It has a very fast pot life (30 minutes) once it's mixed with the converter. Then broadcast aggregate into the coating while wet. If a blush is present, it must be removed prior to topcoating or recoating. CURE SCHEDULE: Norklad 200 is a two component 100% solids epoxy colored coating designed for applications where a high build colorfast impact resistant floor is needed. If a blush is present, it can be removed by any standard detergent cleaner prior to topcoating or recoating. After mixing, transfer the mixed material to another pail (the transfer pail) and again remix. The plastic sheet testing is also a good method to determine if any hydrostatic pressure problems exist that may later cause disbonding. If a primer is not used, more porous substrates may cause outgassing and possible surface defects. Once you get the product out of your mixing bucket it takes much longer for it to tack off. It can be used as durable color coat for for maximum durability or as a colored base coat for color chip broadcasts. We will do our best to keep accurate stock availability online. There are no harmful organic vapors (VOCs) like you experience with urethane application.