2) Screw the threaded part of t

2021/05/21

2) Screw the threaded part of the fitting onto the copper pipes fitting. Thanks!!! In other news, after reading your imaginary British person conversation above, I decided you would be someone awesome to hang out with in real life. It also said WD40 helps loosen things if you spray it into the threading and wait a few minutes. Make sure you have at least two trays on hand to catch water. Lay down plastic wrap and a shallow tray under the spot youre going to cut. You can do it!! My preference is to connect that brass pex fitting to the threaded galvanized pipe after removing the elbow, but if I run into problems or damage the threads or whatever, my backup solution is to cut the galvanized and use a (galvanized) connector (as in photo) to connect to the pex. My wife and I will be tackling a similar project soon and this was helpful to see. Grrrrrrr!!!!!!! And then of course, rip out the old pipe with your bare hands and growl at it. 11*- Water meter key. This keeps you from breaking anything and gives you a little more turning power. 8- A saw that can cut metal. SharkBite fittings are engineered to provide an extremely fast, secure and reliable method of joining Copper, PEX, Polybutylene and Carbon Steel pipework. STEP 6: Unscrew the pipe ends. Things I learned from other sites. It may not display this or other websites correctly. Get a 2 or 3 foot piece of pipe that will fit over the handles of the pipe wrenches. But before we pushed it into the adapter, we needed to straighten it the best we could. Then we turned on the faucets again just in case and there was water coming out of them! As Evan laid on the floor in defeat and I perched on the counter eating wheat thins, we talked about how we could always stay the night at his parents if we had to. The thing didnt budge. To be safe, do it at your main water valve AND at the meter using a water meter key. Yep, anything that is 5/8 or 7/8 OD. No, I see that the male thread on the German coupler has the same thread as a 1/2" shut off valve that I'm going to install, so it seems to be correct - the other end that goes over the 1/2" galvanized, I assume is ok, but I'm not 100% sure. Before you can actually remove your pipe, you have to cut it somewhere in the middle so that youre actually able to unscrew each end. How do you connect galvanized water pipes? You have to wrap it in the same direction that you screw it in, so clockwise if youre facing the threads (see in the picture below). Make sure the pipe joint compound or tape go into the threads, to ensure a water tight connection. Curtains! We started by prepping the area- we picked an easy to reach section of the pipe we were removing, laid out lots of plastic underneath, and set a tray under where we were going to cut. I have been trying to find out how to attach the threaded part of the pex to the threaded galvanized pipe. 5- Flashlight. Instead of Evan holding onto both of the wrenches, I pushed the one on the joint counter-clockwise as hard as I could while Evan used his body weight to push the one on the pipe clockwise with his foot. Lots of penetrating lubricant is totally great, especially if you can put it on in advance. They can connect pipes with or without threads and are especially useful when threads have rusted and become unusable. Oh happy day!!!!!! PVC is not CTS (copper tubing size=larger OD) so the QEST compression fittings will not go on it. When I did all these things on galvanized pipe not in my attic, it came loose like it was easy. - Evan & Katelyn, http://www.americanvintagehome.com/plumbing_heating_air_conditioning_information/why-you-need-to-swap-out-your-galvanized-pipes/, How to Connect PEX to Galvanized Pipe | A Step By Step Guide, DIY Cat Feeding Station (with splash shield), Finding 2-player loopholes in the Raft Finale (pt.15), Raft went from tropics to snow covered islands?! So Evan ran to Home Depot again while I stayed here to keep an eye on leaks, and he picked up another wrench and some WD40. So, would this coupler be ok for potable water, and be a reasonably permanent repair? If any particular ad is your REASON for blocking ads, please let us know. Easy easy. Turn to the RIGHT(calm down) as to TIGHTEN it. So we decided to just keep all the faucets on the on position and Evan ran to Home Depot to get a water meter key so we could turn off the water at our meter too. Some water will come out, dont panic. Then we just pushed the end of the PEX into the adapter and it was done! Evan and others. 1) Use crimp ring or cinch clamp fittings for a cheap way to connect the tubing. :), Pingback:It's Curtains For Ya! It only took two pipe wrenches, a buttload of WD40, and two adult humans using all their force to unscrew this pipe, but we did it! Its just that everything else took freaking forever. When doing any plumbing, leave all facets open when the water is turned on to relive the air pressure out. Exactly 100% use a dielectric Union between that galvanized pipe and brass fitting youll regret it if you dont it will eat all the rest of that pipe. If an old galvanized pipe comes out from the wall, installing a shutoff valve is usually a straightforward job; simply screw a threaded stop valve onto the pipe. Next youre supposed to run all your faucets, showers, etc until no more water is coming out. a (galvanized) connector (as in photo) to connect to the pex. Thank you! galvanized steel pipe copper join plumbing water pipes dielectric joining corrosion tubing familyhandyman metal repair pex stop unions use diy We needed 25 ft of 3/4 piping, so we got a 50 ft roll just in case. Good luck. Or is none needed between brass and galvanized? This was slightly (VERY) nerve-racking, not gonna lie. 7- Teflon tape.

Crazy! I can see my wife and I doing a similar project in the near future. This is to drain any water that was hanging out up in your pipes. S03E03, Getting COVID and rethinking our lives (#83), Why we filmed a video with appendicitis (#082), #080 Lessons learned from our first house. Luckily its pretty flexible. 1. suggest a 5 gallon bucket also, to dump those trays into. Potential chemical leaching is another downside of PEX piping. Notice all the asterisks. Now not concerned about it. Somehow, even when our main water valve was off, water still got in.

As promised, here is a quick guide to all the steps you SHOULD follow: STEP 1: Turn off your water. Why, hanging out in our attic for six and a half hours of course! Thank you for the tip! previous plumbing experience that involved scooping lots of water with a plastic cup, It's Curtains For Ya! Everyone should consider replacing it all. Whether the adapter fitting is threaded on the galvanized pipe or soldered to copper, connect to the existing pipe. fitting elbows I mean, Id take a culinary blowtorch to a crme brle given the opportunity, and my fiance will not deny that hes a bit of a pyro, but NEITHER of us was about to bring a blow torch into our wood-filled attic. . If possible unscrew the supply tube at the bottom only, so it remains attached to the faucet or toilet above. With the right tools its totally doable! how to connect galvanized pipe without threads. 9*- Trays to catch water drips. We bought one painters tray, but luckily I had some disposable 99 baking trays because we ended up needing those too. PEX tubing is crimped onto the male end, and the female end is either soldered or threaded onto existing pipe. wirsbo uponor pex plumbing pipe tubing aquapex ft water Only thing holding me back was worried about getting the old corroded pipe out of the joint. It took a few minutes and then no more water was coming out so we assumed we were good to go. STEP 5: Bust out the WD40. Apparently warming the metal makes it malleable enough to unscrew. Clamp ring connection First, attach the adapter to the existing pipe. He came back, we tried the WD40 and the additional wrench and still no dice. 3) Slide the crimp ring or cinch clamp over the end of the PEX tubing. We did some online research and found out that you need TWO pipe wrenches one to turn the pipe youre removing, and one to turn the threading its screwed into in the opposite direction. Enter your email to get new post notifications, yay! You must log in or register to reply here. - Evan & Katelyn. Second, when using the 2 pipe wrenches, you want to keep the good pipe from moving (so it doesnt loosen at its other end), so the one wrench holds it in place and the wrench on the bad pipe is the one that should move/turn. Mentioning leaving the water on. Solder the pipe and cap joint at 350 degrees celsius with super alloy-1. There are two spots you can do this- at your main water valve where the supply line goes into your house (usually around one of your hose faucets outside) or near the street where your meter is. Galvanized pipe and brass pipe are both used for water piping systems. Anybody try one yet? There was a steady stream of water trickling from our pipes filling up our tray surprisingly fast. You can get white, blue, or red (the only difference is that red is used to identify hot water, blue is used to identify cold, and white can be either. Please dont bring a blowtorch into your attic. ANYWAYS, we successfully replaced our leaky old galvanized pipe with a fresh new piece of PEX piping! This was a great post. I dont think I could replace a pipe! Its an alternative to PVC or copper pipes that is being more and more widely used due to its low cost and ease of installation. How do you connect non threaded galvanized to PEX? Wow, this is your best blog yet! Thanks. You 100% need TWO for this project! Lead, a dangerous toxin, may build when the pipes corrode. The PEX part WAS easy. Is there any other kind of plastic coupling that would be more suitable in my case? SharkBite makes a threaded to press fit transition adapter to fit your PEX to galvanized. STEP 8: Screw adapter into the joint you unscrewed your pipe from. How do you install a shut off valve for galvanized pipe? Eventually Ill get to replacing it all, but the rest is behind/between walls that require a lot more work to get at. Good tips! thank you both for sharing. Bloody hell! A Dresser coupling made by the Dresser Company is a compression coupling you can use to repair galvanized steel and other metal pipes. At the end of the post Ill list the steps you SHOULD follow in case anyone reading wants to attempt this in their own home. Due to its chemical composition, the PEX pipe material may leach toxic chemicals including bisphenol (BPA), MTBE, tertiary butyl alcohol (TBA), and others.Sep 26, 2018. Simply cut the pipe with a hacksaw, making as straight a cut as possible, then fit a Fernco flexible connector with the appropriate diameter over the end and tighten it down. We use sch 80 PVC everyday for drop pipe when we set pumps, Plumbing Forum, Professional & DIY Advice. For mating your PEX to galvanized, SharkBite makes a threaded to press fit transition adapter. Add a new galvanized steel pipe length (nipple) at each end and solder in your copper. Then we got to actually attach our new PEX! It is flexible, durable, and high-density. In-line fittings are used to connect separate lengths of PEX tubing, to create a branch line, or to add a valve.

CHIP, Pingback:How to Connect PEX to Galvanized Pipe | A Step By Step Guide. We did read about using a metal pipe to extend the wrench, that was our next plan of action if we couldnt get things to work, those metal pipes are like $20 though! Cross-linked polyethylene, commonly known as PEX, is made of plastic, flexible tubing. (Raft pt.14 the final chapter), What new villagers are there with 217 mods?? What you need is an adapter for the size pipe you are connecting. Yeah. They can connect pipes with or without threads and are especially useful when threads have rusted and become unusable. Whoops. You have to wrap the threading on the adapters, the same way you wrap a shower head when you replace it. Silly Texas person. Luckily there was pretty much no water to deal with this time. It was not as tough as we thought it would be :). Shark Bite push-to-connect fittings are not designed to push on galvanized pipes. No WD40. how to connect galvanized pipe without threads, Remove all traces of rust and old pipe joint compound using a stiff wire brush. You will need to square cut the end of your galvanized pipe and then rethread it. It looks like you're using an ad blocker. We will keep our eye out for any erosion- we check every so often and so far it looks to be ok, but thank you for the heads up! So, the typical Pex compression fittings (as in the first photo) are fine to connect to Galvanized? Connecting together galvanized pipes that are non-threaded uses a coupling that creates a sealed joint. I used the more reliable source, http://www.epa.gov for information, but I wanted to share this one, too, for the photos: But we used a slightly different technique this time (after spraying again with copious amounts of WD40). Align the coupling end with the drawn line on the pipe. You know I love a man with nice PEX. Galvanized plumbing could pose a dangerous health hazard if not replaced with updated, safer pipes. http://www.homedepot.com/p/LDR-InduFPT-Compression-Coupling-311-CCL-12/100566707, https://www.amazon.de/Gebo-Armaturen-Temperguss-Klemmverbinder-Zoll-01-150-00-01/dp/B0017VC9VE, http://www.deaconind.com/Customer/DEINSU/specpages/Dress_65.pdf, https://www.reddit.com/r/askscience/comments/35ypgu/why_do_plumbing_dielectric_unions_always_fail/, http://www2.iccsafe.org/states/new_york/NY_Plumbing/PDFs/Chapter 6.pdf, https://up.codes/search?previous_puq=galvanized&category=new_york_city&year=2014, Age old question of brass fittings into stainless, Moving 1.5" copper vent pipe exposed during kitchen soffit removal. Not likely to happen. Use two pipe wrenches pulled in opposite directions, one gripping the pipe you are unscrewing and one gripping the joint youre unscrewing it from. Leave them open til youre done with the project, just to be safe. Ive looked for them lately and have not been able to find more for the complete change out that Im planning.